ASTM A234 WPB Elbows

ASTM A234 WPB Elbows
ASTM A234 WPB Elbows
We are manufacturer of ASTM A234 WPB Elbows and supply high quality ASTM A234 WPB Elbows in both large and small quantities worldwide and offer you the best prices in the market.

Weld Elbows: DN250 - DN1800
Seamless Elbows: DN15 - DN700
Wall thickness: STD, XS, XXS, SCH10, SCH20, SCH30, SCH40, SCH60, SCH80, SCH160 and ETC
Bending radius: R=1.5D-10D
Bending angle: 45°, 90° and 180°

Standards:
ASME: ANSI B16.9, ANSI B16.28, MSS SP75
DIN: DIN2605, DIN2615, DIN2616, DIN2617 and DIN28011
SGP: JIS B2313
EN: EN10253-1, EN10253-2

Materials:
ASTM:
Carbon steel: A234 WPB
Stainless steel: A403 WP304, A403 WP304L, A403 WP316, A403 WP316L and A403 WP321
Alloy steel: A234 WP12, A234 WP11, A234 WP22, A234 WP5, A420 WPL6 and A420 WPL3
DIN:
Carbon steel: St37.0, St35.8 and St45.8
Stainless steel: 1.4301, 1.4306, 1.4401 and 1.4571
Alloy steel: 1.7335, 1.7380, 1.0488 (1.0566)
JIS:
Carbon steel: PG370, PT410
Stainless steel: SUS304, SUS304L, SUS316, SUS316L and SUS321
Alloy steel: PA22, PA23, PA24, PA25 and PL380
GB: 10#, 20#, 20G, 20g, 20R, Q235, 16Mn, 16MnR, 1Cr5Mo, 12CrMo, 12CrMoG, 12Cr1MoV, 12Cr1MoG, 12Cr1Mog, 12Cr2Mo, 12Cr2MoG, 15CrMo, 15CrMoG, 15CrMog, 15CrMoR.

Get in touch

Welcome to Sunny Steel Enterprise Ltd.

Sunny Steel provide a wide range of steel products as Steel pipes, Seamless tube and seamless pipes, Alloy pipes, Pipe fittings, Composite steel pipe used in the industry, construction etc.


Contact Form

Name

Email *

Message *

Popular posts from this blog

Barred Tee

Image
A barred tee is a tee or any fitting with a branch used in pipelines that is pigged and has a restriction bar welded internally preventing the pig from traveling down a branch connection. Barred tee is a pipe fitting that is used in a pig launcher or receiver system in a piping system to ensure the pig could pass the branch safely. Design considerations for barred tee The barred tee will be used when there is a requirement for pigging. Thus, many of its applications can be found in the pipeline or in the subsea field. The bar plates that welded internally at the branch are to avoid the pig from changing direction or getting stuck at the branch outlet. The design of the bar plates must be in sufficient quantity, thickness and adequately spaced to ensure the smoothness for the pig to run through the main pipe, and at the same time not affecting the flow that was meant to flow through the branch. Normal practice is to ensure that the opening in the branch pipeline after gui
Read more

How to Calculate a Pipe Bend?

Image
Pipe fittings are necessary to join together pipes, or to change the direction of an existing pipe. Pipes and pipe fittings are made of a variety of materials, depending on the fluid or gas being transported. Most pipe fittings tend to be either threaded or able to slip over the pipes they connect. Whether you are using steel pipes of PVC pipes, a chemical solvent is required to create a seal between the pipe and the fittings. Measure the required length of the pipe to be installed, keeping in mind the extra length required where the pipe will be inserted into the fitting. Mark this length on the pipe. How to Calculate a Pipe Bend Whether you are bending pipe for running electrical conduit or a metal project, calculating the bend for the start and end point can be an important factor. While there are different types of pipe benders on the market, they all share a common identification for the operation. Identified on all pipe benders is the size of pipe the unit will bend alon
Read more

Saddle previously

Image
Saddle previously is the ventilation ducts 'crotch tee', its shaped like pants, there Equal and unequal diameter, the formal name is "tube tapered pants tee." Carbon steel saddle previously There is no standard size, to be based on three tube spacing center line of the front and graphic design draw graphics, Lofting produced, lofting a certain degree of difficulty. We are manufacturer of Saddle previously and supply high quality Saddle previously in both large and small quantities worldwide & offer you the best prices in the market. Size range: 1/2 to 72 inches Sheet metal is engaging, steel welding. Industrial Processes Type: Sweepolet Saddle, Steel Saddle, Carbon Steel Saddle, Stainless Steel Saddle, Alloy Steel Saddle Applications of saddle previously: Saddle previously is to replace the existing tee fitting, the use of flexibility, praised by domestic and foreign markets. Saddle pre
Read more